Hey guys whats up I'm Nick other wise known as Dirty South PC Mods. Going to be working on a build for my Gamer Girl that likes Spiders.
First off I would like to thank my Sponsors.
Thank you for your support
Secondly I would like to thank my two fave stores that I buy all my gear at.
Ok so lets get this build started.
Ok here is our Motherboard an ASRock Z77 Extreme 4 1155.
The heat sinks didn't really go with my overall theme so we are going to paint them Pink. First I taped the Contact Points of the Heatsinks.
Then we shot them with Etching Primer
And then with Krylon Floresent Pink.
There we go much better.
Used a Koolance double sided male coupler between the Phobya 400 Pump and the Primochill CTR
Prepping the Fans for there Pink Doom :P
Since you can't use regular spray paint on Plastic We first used Krylon Fusion in white as a primer and will be shooting the Pink over that for all the Plastic parts.
Attachment 751Attachment 752Attachment 753
Attachment 754Attachment 755
The Phobya 400 Pump is going to get the same treatment.
This is the case we will be using in our build. A CoolerMaster HAF 922..We are going to be cutting a full window, Trimming the 5.25" Drive cage down from 5 slots to 2, Removing the HDD cage. And paint the Motherboard Tray, whats left of the 5.25 Drive cage, I/O plate and front panel mesh Pink.
Shes Naked!!!! Time to pop some Rivets
Ok we removed the IO/Expansion slot plate, Motherboard Plate, HDD cage(went in the trash) and 5.25" drive cage
Some White Primer on the IO/Expansion Plate
First Coat of Primer on the Mobo plate
Now while we wait for the Primer to dry. We are going to get started on the cuts we need to make.
Measuring up for the Side Panel Window cut.
Always use an Awl or old screwdriver thats been stripped to mark your drill holes to keep your drill from walking
We wanted rounded corners so we are going to use a drill for the corners
Ok most use a Dremel or a Jigsaw. I prefer my 90,000 RPM air powered cut off wheel. Cuts through Aluminum and 1/4" Steel Like a Hot Knife through Butter
Same tool was used to trim down the 5.25" drive bay from 5 to 2 slots
Let The Pinking Begin
Pops shooting the last of the Clear Coat
Alright the first set of Icemodz cables are here
Here is a Link to the Unboxing Video we did for them. http://www.youtube.com/watch?v=JfUj9sFNxs0
Man thats a bright Pink.
Alright so I ordered some Pink Di-noc and some Mirrored Pink Film for the CPU Block and the Lamptron FC-2 Fan Controller we will be using
Here is the Water Block will be using for the CPU its an older OCZ Hydroflow from about 2009
Wrapped the Chrome Portion of the CPU Block in the Pink Mirrored Vinyl
Got the Case riveted back together and the ASRock Z77 Board with our OCZ Block on there not too shaby!!
Got a first Radiator Installed the XSPC 240mm Rad in the Front where the HDD cage Had formerly been.
The Primochill 120 CTR UV Pink Res and Phobya pump in there
Ok not to crazy about the Pink Mirrored Vinyl going to try the Pink Di-Noc
And now for the Lamptron FC-2
There Optical Drive is receiving the same treatment
And I don't like it at all. going to tear it off and paint them to match the rest of the front panel.
There much better
Found a cool Halloween decoration with Spiders on it and made it fit in the case. Also just got the Primochill Advanced LRT Tubing UV Pink
Wrapped the PSU in Pink Di-Noc to Match the CPU
Got the BSMODS 5050 RGB LED Strip installed. This thing is awesome I highly suggest going to the site and getting a set http://www.bsmods.com/Mod_Shop.php
Also here is a short unboxing and demo video of the Product in action
Ok we got her all tubed up going to be adding a second 240mm crossflow Rad to the top later
Ok was thinking of sleeving these Front Panel Wires But I got a better Idea.
I found some UV Pink 18g wire so I am going to change out all the FP wires to this wire
Here is a look at a crazy color change effect in the Black Light.
Got the 120Gb Kingston SSD Mounted behind the Mobo plate.
This is our Video Card EVGA GTX 550Ti. Going to be custom Painting it and the New Xigmatek PSU with a Spider Web Design
Xigmatek 700 watt PSU I picked up from PPC's on clearance for $25 It to will get the same Custom Web patern
Got the New Icemodz Custom Cables and UV LED Lights in there check out his site he does awesome work. http://www.icemodz.com/
Also here is another video of the unboxing and Demo of the lights Outside as well as Inside the case.
Well thats it for now guys I'll install the Newly painted PSU when I get the second Rad, GPU Block and Flow Indicator in.
Feel Free to stop by the Dirty South PC Mods Facebook Group page and Terror-Byte Gaming Page
BS MODS Facebook Page
Icemodz Facebook Page
As well as our Youtube Channel for awesome Unboxings, Reviews, Game footage and more!!!!
See you soon