Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Maul (modded Corsair 600C) by SimpleModz

  1. #1

    Maul (modded Corsair 600C) by SimpleModz

    Hi guys,

    Welcome back to another one of my build logs. I'm pretty excited for this one

    It will be based on Darth Maul and incorporate some interesting ideas with the Corsair 600C case!

    I did a video covering the case, fully disassembling it as well as talking about the mods!

    Check it out below:



    SPECS:

    Case - Corsair 600C
    CPU - Intel Core i7 6700K or 7700K
    MB - ASUS MAXIMUS VIII Extreme
    RAM - 4 x 8GB Corsair Vengeance Red LED 2666MHz DDR4
    GPUs - 2 x ASUS STRIX GTX 980Ti
    SSD - 3 x 240GB Corsair Neutron XTi
    HDD - 2 x Seagate TBC
    PSU - Corsair RM850X

    Custom cables and lighting - CableMod

    Water cooling - Bitspower

    Here are also some photos of the case to start off with





























    Thanks for checking it out and stay tuned for more!

    Cheers,

    Alex

  2. #2
    Two of the 3 mods I'm currently working on

    Maul is the one on the left in the Corsair 600C and the shell on the right is the Cooler Master MasterCase Maker 5t, this is my Tempest Mass Effect mod.



    I already did some cuts in the 600C. Mainly the front panel section as well as the top. A bit more filing and tidying up of the cuts need to be done but it's coming along well so far









    Stay tuned for more

    Cheers,

    Alex

  3. #3
    Hey guys,

    I took apart the top and front panel further and did the cuts into the plastic part while I get the metal parts ready



    The front panel 5.25" door cut out window



    Top panel cut out window



    Top panel metal part





    Front panel metal parts



    Thanks for checking it out and stay tuned for more!

    Cheers,

    Alex

  4. #4
    Stay tune for Maul










  5. #5
    Here is what I'm currently working with! Imagine the horns and eyes lighting up once the build is finished! I'm also going with a battled and worn out weathered theme as well.

    Everything was cut manually with a jig saw and a lot of filing. The cut-out at the top is a small window that will look into the top compartment.

















    Stay tuned for more!

    Cheers,

    Alex

  6. #6
    Hey guys,

    Time to start focusing my attention back to this build log and get it all up to date! I've been pretty busy as always however the build is finished and I will unveil it over the next couple of days.

    I just want to show you guys all the progress first and I still need to take final photos and film it.

    I'll start with two massive 10TB Seagate IronWolf HDDs that are going in the build, a plethora of red Bitspower fittings and the simple weathering effects done to the case.





























    Hope you guys like it. Same as the front panel that I shared before, I wanted the build to look like it's been through a Star Wars space battle. The paint effects were done by dry brushing some simple acrylic paint, a very easy effect to achieve. You can also see an acrylic motherboard skirt cover panel.

    Stay tuned for more!

    Cheers,

    Alex

  7. #7
    Hey guys,

    The motherboard I'm using is the ASUS Maximus VIII Extreme with a full cover Bitspower Monoblock that I decided to remove the top cover from and have it exposed. The acrylic would probably do with some polishing however for this build, in terms of the other aesthetics, I think it should work well as is.











    The two ASUS STRIX GTX 980Tis, still pretty good cards even today, with Bitspower full cover water blocks.













    And the memory I'm using is the Corsair Vengeance red LED





    They're pretty good how you can easily remove the tops to orientate the Corsair logo to better suit your build.







    The tops could even be painted quite easily for further customisation.



    And here's everything mounted inside, with tubes in so I can mark for the pass-through fittings on the front panel.







    Thanks for checking it out and stay tuned for more!

    Cheers,

    Alex

  8. #8
    Okay, here we go, pass-through fittings are mounted and the front acrylic cover panel is complete.













    You can also see the motherboard skirt panel is ready as well, with reservoir mounts on.







    Fans are going underneath the case and a 60mm thick radiator on top of them in the bottom of the case. I just wanted more room and the fans fit nicely underneath. Plus, they will give a nice glow underneath the case.







    Thanks for checking it out and stay tuned for more!

    Cheers,

    Alex

  9. #9
    Hi guys,

    Here's most of the piping done!

    One issue I had with this is that two of the pass through fittings were way too close to each other and I only had Bitspower C47 style fittings that were a bit too large. So I ended up hand filing them down.

    This was the result:





    Just shaved off a few mm and they fit perfectly with a bit of tubing between them.

    They're the ones at the very bottom.







    Mounted the RGB LED controller for the Corsair fans in the front as well. This will be accessible from the side even with the front panel on.



    And here's a look at the cable management.



    And now the inside.



    The red chrome tubes, with the fittings in the middle is a reference to the dual lightsaber.















    Thanks for checking it out and stay tuned for more!

    Cheers,

    Alex

  10. #10
    Hey guys,

    These were the final photos I took before getting all the panels on and finishing the build





















    As you can see, I went with black coolant and I also have a few red cold cathodes in there just for some more lightsaber references

    Stay tuned for final pics!

    Cheers,

    Alex

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 570TRIX (modded Corsair 570X) by SimpleModz
    By alexciobanu in forum Modding Work logs
    Replies: 11
    Last Post: 03-22-2017, 01:28 AM
  2. IN WIN DUKE (IN WIN D-Frame 2.0 custom build) by SimpleModz
    By alexciobanu in forum Modding Work logs
    Replies: 18
    Last Post: 12-13-2016, 10:09 PM
  3. MODWARS - Tekno Angel (Tt Core P3 Mod) by SimpleModz
    By alexciobanu in forum Modding Work logs
    Replies: 12
    Last Post: 11-30-2016, 04:37 AM
  4. PROJECT ALPHA OMEGA (modded Corsair SPEC-ALPHA)
    By alexciobanu in forum Modding Work logs
    Replies: 15
    Last Post: 11-30-2016, 04:29 AM
  5. [Project Log] TOXIC CHROME (modded Corsair 250D)
    By alexciobanu in forum Modding Work logs
    Replies: 34
    Last Post: 01-10-2016, 05:10 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •