Results 1 to 5 of 5

Thread: Project: Hades

  1. #1
    Darwin's Avatar
    Join Date
    Apr 2016
    Location
    UK
    Posts
    22

    Project: Hades



    Hello and welcome to Project Hades by Darwin PC!


    Introduction

    Hades was the ancient Greek god of the underworld, a son of Titans and brother of Zeus and Poseidon. As Project Hades will feature an inverted ATX conversion, the underworld theme made sense. I have a few mods planned to make this build stand out.


    Hardware

    • Case: Cooler Master MasterCase Maker 5
    • Motherboard: Gigabyte GA-Z170X-Ultra Gaming
    • CPU: Intel Core i5-6600K
    • GPU: Palit GeForce GTX 1060 Super JetStream
    • Memory: Kingston HyperX Savage 32GB (4 x 8GB) DDR4
    • PSU: Cooler Master V1000 1000W 80+ gold modular
    • CPU cooler: Cooler Master MasterLiquid Pro 240
    • Cabling: Custom-sleeved with E22 Teleios



    Sponsors

    Thanks to the following sponsors for making this project possible: Cooler Master, Gigabyte, Palit and Kingston / HyperX.


    Updates

    1. Hardware
    2. Test build
    3. Case modding pt. 1
    4. Case modding pt. 2
    Last edited by Darwin; 08-01-2017 at 02:43 PM.

  2. #2
    Darwin's Avatar
    Join Date
    Apr 2016
    Location
    UK
    Posts
    22
    A few shots of the hardware - looking forward to playing with this!










































  3. #3
    Darwin's Avatar
    Join Date
    Apr 2016
    Location
    UK
    Posts
    22
    I did a quick test build to make sure everything was working. Assembly was straightforward, although it took some clever positioning of the CPU cooler radiator and fans to not put strain on the tubing.

    The test build booted perfectly first time, and with no SSD connected, went straight into the UEFI/BIOS.

    The CPU temperatures were good, and the BIOS made easy work of adjusting the fan curves and pump speed. I did have to swap the pump cable to a different fan header, as the ‘pump’ header on the mobo couldn’t control the speed (in voltage or PWM mode). It worked fine on a different header though.












  4. #4
    Darwin's Avatar
    Join Date
    Apr 2016
    Location
    UK
    Posts
    22
    I began work on the case modding. The first task was to invert the motherboard.

    Here's the case during stripping down, with most of the panels removed.



    Most of the removeable modules use these retained thumbscrews, which I find pretty useful for not losing the things.



    This is the fan and LED controller on the back.



    All parts removed from the case.



    The case completely stripped down.



    Checking the placement of the motherboard within the case.



    Starting to drill out rivets. I had originally planned to completely disassemble each section, but then decided to keep the middle section intact, and remove the top and bottom sections then swap them over.



    Removing rivets from the corner brackets.



    Bottom section removed.



    Top section removed.



    Checking alignment for reassembly.



    There was a lip in the middle of the top section that prevented the corner joints from lining up.



    I cut off the lip with the Dremel.



    Here is the top section in place.



    On test fitting the IO panel, I found it was blocked by another lip on the front section.



    This part was also removed.



    Edges cleaned up ready for the IO panel.



    The IO panel now fits perfectly.


  5. #5
    Darwin's Avatar
    Join Date
    Apr 2016
    Location
    UK
    Posts
    22
    To complete the ATX motherboard inversion for the Cooler Master MasterCase Maker 5, the pieces were reassembled and secured by rivets.

    Holes where rivets had been drilled out were measured using digital calipers. Here are the rivets, in black, with various sizes to fit different thicknesses of material.


    Here is the heavy duty pop rivet gun to be used for assembly. It is pretty hefty, but clearance in tight spaces can be an issue.


    The case was reassembled without any issues. The case now works just as previously, but with everything upside down.






    I then put together a quick test build to check everything fits properly upside-down...




    ... and added the plastic panels.



Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 25
    Last Post: 04-10-2017, 12:19 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •