[Build Log] Metroid -A 3D printed computer case

[thorkon]

Getting near the home stretch!

Heres a test lighting of one of the feet. No cable management yet...ha



Side being built up:






Not fully complete but just an idea how the window will be


I'll be back when I have the whole top finished with fans and whatnot. I'm gonna start working on getting the leds wired in

Heres a test run with them shoddily taped on the inside

[thorkon]

Finished up the frame of the top!


Couldn't use any vertical clamps due to the say its smooth on the inside, so had to use some weights to help glue it down.


Baby for scale



Adult for scale


This is my wife staying "awake" past her bedtime trying to help by routing the pc wiring on the inside


Now I'm moving on to the LED wiring on the inside. Its going to be awhile of wiring and soldering... Heres what a pattern/schematic of the led paths

[thorkon]

Back now that I'm done with the wiring. Oh boy, was this an adventure. I've rarely done soldering/wiring and this has definitely increased my skill with it ha. There will be gifs of the lighting, I'll provide a link if the message board isn't showing it natively.

So my first test was my lazy test, which to say was I was hoping i could just fold the led strip to make 90 degree turns but I didn't like the way the lights would repeat flash whenever it came to a bend...

GIF of Light issue

https://imgur.com/IeL0tHB

I decided to cut the led strip and solder whenever there was a 90 degree turn. Heres the same layout, but with wiring instead of folding

GIF of Light fixed
https://imgur.com/Am1TJAy


Next is some wiring shots
Splitting off the led strip



The monotonous monotony of stripping wires and tinning wires



The finalized wiring on the inisde with everything hotglued in place. I'll need to print some covers to hide the wiring and clean it up.


and finally one section lighting up in the dark
Gif of section lighting up

https://imgur.com/KNzvVWC

Next is programming the ASUS Tinkerboard so that the led strips will run on seperate timings. I'm just delving into this so should be interesting

[ellascott]

This is exactly what I’ve been looking for. geometry dash

[thorkon]

Just a small update of all the lights running
heres a link if gif embed doesnt work: https://imgur.com/VMuIZOR



Still working on trying to program the coding so they run seprately atm

[thorkon]

Turns out programming isn't as easy as I had hoped. I have a friend or two giving me a hand. In the meanwhile, I picked up 2 more sponsors! This is greatly appreciated and welcomed.

First off is GEIL with supplied 2x8gb SUPER LUCE 2400 DDR4 RGB Ram





Next is ThermalTake who graciously supplied RGB fans, PSU, and a sweet CPU cooler


Engine 27 CPU cooler (first time for me seeing an all metal fan, looks awesome!)



Thermaltake Toughpower Series PSU SFW 600W


Thermaltake Riing Plus 12 RGB Fans + TT Sync Controller

[thorkon]

Back again! I've been doing small things that didnt warrant many photos (trying to learn to program, ended up having my 2 buddies help me), and rearranging computer components.
I'm nearing completion though! I will probably have 1 more update after this then it will be final photos and a time lapse video of the build/3D print process. My buddy is working on the music for that video atm. Anyway, on to the smaller update here:

This is the rear of the case. Its fitting the Thermaltake Riing RGB fan. I wanted to keep the fan removable because I need to get my hand in the computer case to plug the fans in once I put the top on. I ended up using magnets to hold the fan in place (located at each corner).




This is the top of the case with another Thermaltake Fan. This is permenantly installed in the case no need for removal here.


This is experimental. I'm using translucent red plastic to use as pseudo cable sleeves for psu/power button/Asus 1080 card. I think it looks good, but what do you think?


Also you can see I went with Thermaltakes Riing Cpu cooler. I was afraid it would be too tall but it is about an inch short of hitting the top of the case so no worries.

[thorkon]

Probably last update until the final photos and video! I'll have it at PAX East 2018 if anyone is going to be there by chance.
Got the lighting done! I have it wired into the PSU so it doesn't need additional outlets to be plugged in.



This is the window side. Just printed some flat sides to cover up gaps the acrylic window leaves.


These are little "feet" that help guide the top frame onto the body. They are angled so the top section slides on them.


Next is I decided to self-promote on the SSD since it was looking bland anyway




My finalized wiring job


Be back in a week or two with the final photos! (probably post video a little after that).

[thorkon]

Video is done! Link is under here, will be back with photos soon!

[thorkon]

Large photo dump inbound!!!!!
Specs:
-ASUS ROG Strix X370-I

-ASUS GTX 1080 Turbo

-GeIL 16gb DDR4 Super Luce RAM

-Thermaltake SFW Toughpower 600w fully modular PSU

-Thermaltake Riing RGB Fans (120mm, 200mm, Cpu cooler)