Top ad

Collapse

Intro to Modding: A Basic Toolkit

Collapse

Announcement

Collapse
No announcement yet.
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Dewayne
    replied
    Intro to Modding: A Basic Toolkit

    I have the same one and works great.

    Leave a comment:


  • Computer_Tinker
    replied
    Intro to Modding: A Basic Toolkit

    I would like to add this:

    A bending brake for sheetmetal and aluminum. Heres a link to one for only $35 USD. 18" max. stock size yet portable.

    http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=39103

    I found it works great when bending modders mesh and other items as needed.

    Leave a comment:


  • sh4rkbyt3
    replied
    Intro to Modding: A Basic Toolkit

    Two more things I'd add.

    1) An auto center punch opposed to the standard center punch. They are a little more forgiving on denting the case metal.

    2) Since most cases are black I'd include either a Silver sharpie which has a finer point than a regular sharpie or a paint pen (preferably yellow or white) but use the paint pain only if your going to be sanding the surface since there output isn't very fine. Light tape and a black sharpie will do the same thing but a light colored marker (Silver, White or Yellow) will save you the tape step and a little time.

    Leave a comment:


  • Virtual-Slay3r
    replied
    Intro to Modding: A Basic Toolkit

    I am always wondering what kind of tools I need to mod my computer up! Thanks alot! I will buy all of these tools and begin modding my case. I need more room for my case so I'm going to try and make a bottom piece. Thanks once again!

    Leave a comment:


  • bluepencil
    replied
    Intro to Modding: A Basic Toolkit

    From youre tools it looks a bit simple....

    i will try to get some of those pieces!

    Leave a comment:


  • Raptor
    replied
    Intro to Modding: A Basic Toolkit

    for cutting plexi-glass on them striaght cuts , a hacksaw blade is a very useful tool . when breaking the plexi that is not cooperating ( bending and breaking elsewhere where you intended ) just the blade itself and a pair of gloves come in handy again unless you prefer the hamburgered fingers ....

    Leave a comment:


  • Xyvotha
    replied
    Intro to Modding: A Basic Toolkit

    wet/dry sanding paper of different grits, you never have enough!
    most commonly used grits are: 80/100/200/800/1500 or 2000

    Leave a comment:


  • DB
    replied
    Intro to Modding: A Basic Toolkit

    Done .. thanks for pointing that out

    Leave a comment:


  • SpartanIV
    replied
    Intro to Modding: A Basic Toolkit

    i think a soldering iron and solder should be on there too.

    Leave a comment:


  • leroy
    replied
    Intro to Modding: A Basic Toolkit

    just brought a nibbler, and am in the process of making a hole in the side of a case, jut to try it out.. working well, though hard to find one.

    Leave a comment:


  • DicKspLash
    replied
    Intro to Modding: A Basic Toolkit

    TechParadox great thread

    Leave a comment:


  • TechParadox
    replied
    Intro to Modding: A Basic Toolkit

    I'll add it on to the list. I didn't pick one up until I had a specific need for it, but it is definitely a valuable part of my toolkit.

    Leave a comment:


  • Xyvotha
    replied
    Intro to Modding: A Basic Toolkit

    I'm also a nibbler fan. It's simply the most versatile and cheap cutting tool you can find, either for small 60mm fan holes or a whole side window. Did i mention it won't bother your neighbours?

    Leave a comment:


  • DB
    replied
    Intro to Modding: A Basic Toolkit

    Good list
    I'll add one more basic tool that seems to be much over looked these days ... a nibbler. It only costs about 10 bucks and is very useful , I did all my case cuts with one

    DB

    Leave a comment:


  • TechParadox
    started a topic Intro to Modding: A Basic Toolkit

    Intro to Modding: A Basic Toolkit

    Tools one should have to begin case modding
    --

    **First and foremost, above all else, get a pair of Safety Glasses (or Goggles)! A pair of these will set you back a couple bucks and shelling out a few dollars is better than getting a hot metal shaving in the eye, isn't it?**

    1. A Dremel or other rotary tool. These are invaluable for both cutting and grinding.

    2. A variable-speed drill. Used to drill (and cut) holes in cases.

    3. A 3" hole saw. Either buy separately or in a kit. Works wonders for cutting blowholes for 80mm fans.

    4. A center punch. Used to make small dents or pilot holes for drilling so you don't go skittering across your case with the bit and wreck your finish.

    5. A set of drill bits that are rated for drilling through metal. You'll need at least a 3/16" bit to drill holes for case screws. The smaller ones can be used to punch holes for wires through the metal as needed.

    6. A jigsaw and metal-cutting blades. Excellent for long, straight cuts and/or gentle curves.

    7. A set of files (or grinding wheels for the Dremel). Used to take the burrs off of the metal you've just cut apart. No sense in slashing your fingers open and bleeding all over your work, right?

    8. Masking tape. A must-have for masking off the cutting areas so as not to mar the finish on your case.

    9. A CD blank (or one that your burner screwed up). The best template for a 120mm blowhole you'll ever find.

    10. Sharpie markers (or pencils, or something else that will mark on your case surface). Used to mark out where the cuts/holes will be.

    11. Extra fan grates (various sizes). The best template for figuring out where the holes for the mounting screws should go.

    12. Leather Gloves. A nice heavy-duty pair will make handling the metal you just cut a lot easier and will save your fingers from getting shredded on the edges while you are working.

    13. A Nibbler. The hand-held models are good for taking small areas out of thinner metal, but don't try to use it for any extended length of time without the aforementioned pair of leather gloves.

    14. A Multimeter. A must-have tool for anyone who does a lot of circuit-creation or for checking the rails on your power supply.

    15. A pencil type soldering tool and small diameter rosin core solder .. good for LEDs, wiring, and the afore mentioned circuit creation

    16. A variety of wet and dry sandpaper, in several grits: 80, 100, 200, 800, 1500 and 2000

    - - - - -

    These are just some basic tools that you should try to accumulate before diving in to the hobby of modding. Remember, when modding anything goes, so the best tool you can use is your mind!

    - - - - -

    This list is by no means comprehensive, and is in fact a living document. Feel free to throw in what you feel should be in every modder's basic toolkit, and I'll try to get it added to the list!
Working...
X