Network HardwareStorage Devices

QNAP TAS-268 Dual Bay NAS review

« QNAP QTS 4.2 User Interface | Network test results »

Testing Methodology

Testing Methodology

System Configuration
Case Cooler Master Cosmos II SE
CPU Intel i7 4770K
Motherboard MSI Z97m Gaming
Ram 2 GB G.Skill F3-12800CL9q DDR3-1600
Hard Drives Samsung 840 EVO 256gb SSD
Western Digital black 500 gb 7200 RPM HDD
Power Supply NXZT Hale v2 1000 Watt power supply

4 Seagate 4 TB 7200 RPM desktop drives were installed and used in the NAS tests.

A dual port Intel network card was installed in the test system.

The QNAP TS-563 in all RAID arrays used a Single Static Volume.

In our testing I used the Thecus N5550, QNAP TS-451, & the Seagate DP-6 to get comparison numbers against the QNAP TS-563. The QNAP TS-563 shipped with 8 gb of RAM.  The Seagate DP-6 used 4 drives and 2 GB of RAM. The other NAS devices use 4 GB of ram and the same Seagate NAS hard drives.

Network Layout

For all tests the NAS was configured to use the a single network interface. One CAT 6 cable was connected to the Cisco 2960 from the NAS and one CAT 6 cable was connected to the workstation from the switch. Testing was done on the PC with only 1 network card active; the Killer network card and the corresponding software were disabled for the testing.  The switch was cleared of any configuration and left in a unconfigured state. Jumbo frames was not enabled and no changes to the network interfaces was made.


All testing is done based off of a single client accessing the NAS. We are currently working on a multi-client testing solution. Stay tuned.

To test NAS Performance I used The Intel NAS Performance toolkit and Atto Storage benchmark.

The Intel NAS Performance toolkit simulates various tasks for storage devices such as video streaming, copying files and folders to and from the NAS as well as creatingcontent directly on the NAS. To limit caching, a 2GB G.Skill memory module was used in all tests. All options in the Performance toolkit were left that the defaults. The NAS performance test is free to download. You can pick up a copy for yourself here.

All tests were run a total of three times then averaged to get the final result.

RAID 0, RAID 10, and RAID 5 are all tested.

Tests were run after all the RAID arrays were fully synchronized.

For real world testing, I copied a 4.3 gigabyte ISO file from the SSD in the test PC to the shared folder on the NAS. 4.3 gigabytes of MP3 files were copied over as well.


RAID Information

QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 1 QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 2 QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 3
QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 4 QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 5 QNAP TAS-268 Dual Bay NAS review android, NAS, QNAP, RAID 0, RAID 1 6
Images courtesy of Wikipedia


JOBD or Just a Bunch ODisks is exactly what the name describes. The hard drives have no actual raid functionality and are spanned at random data is written at random.

RAID 0 is a stripe set and data is written across the disks evenly. The advantage of RAID 0 is speed and increased capacity. With RAID 0 there is no redundancy and data loss is very possible.

RAID 1 is a mirrored set and data is mirrored from one drive to another. The advantage of RAID 1 is data redundancy as each piece of data is written to both disks. The disadvantage of RAID 1 is write speed is decreased as compared to RAID 0 due to the write operation is performed on both disks. RAID 1 capacity is that of the smallest disk.

RAID 10 combines the 1st two raid levels and is a mirror of a stripe set. This allows for better speed of a RAID 0 array but the data integrity of a RAID 1 array.

RAID 5 is a stripe set with parity. RAID 5 requires at least 3 disks. Data is striped across each disk, and each disk has a parity block. RAID 5 allows the loss of one drive without losing data. The advantage to RAID 5 is read speeds increase as the number of drives increase but the disadvantage is write speeds are slower as the number of drives is increased. There is overhead with RAID 5 as the parity bit needs to be calculated and with software RAID 5 there is more of a performance hit.

RAID 6 expands on RAID 5 by adding an additional parity block to the array that is distributed across all the disks. Since there are two parity blocks in the array more overhead is used with a RAID 6 array.

For a full breakdown of RAID levels, take a look at the Wikipedia article here.

RAID configurations are a highly debated topic. RAID has been around for a very long time. Hard drives have changed, but the technology behind RAID really hasn’t. So what may have been considered ideal a few years ago may not be ideal today. If you are solely relying on multiple hard drives as a safety measure to prevent data loss, you are in for a disaster. Ideally you will use a mutli-drive array for an increase in speed and lower access times and have a backup of your data elsewhere. I have seen arrays with hot spares that had multiple drives fail and the data was gone.

Do yourself a favor and read up on the different types of RAID arrays and plan accordingly. Personally, I use a RAID 10 array with an automated backup to the cloud. I feel with that setup, I’ve done what I can to keep my data safe.


Previous page 1 2 3 4 5 6Next page
Become a Patron!

Tom Brokaw

Tom is a network and computer hardware enthusiast. He has been reviewing hardware products around for various sites around the net since 1999. He has modded a few cases back in the day.
Back to top button